Influence of Plasdone™ S630 Ultra-an Improved Copovidone on the Processability and Oxidative Degradation of Quetiapine Fumarate Amorphous Solid Dispersions Prepared via Hot-Melt Extrusion Technique.

In a formulation, traces of peroxides in copovidone can impact the stability of drug substances that are prone to oxidation. The present study aimed to investigate the impact of peroxides in novel Plasdone™ S630 Ultra and compare it with regular Plasdone™ S630 on the oxidative degradation of quetiapine fumarate amorphous solid dispersions prepared via hot-melt extrusion technique. The miscibility of copovidones with drug was determined using the Hansen solubility parameter, and the results indicated a miscible drug-polymer system. Melt viscosity as a function of temperature was determined for the drug-polymer physical mixture to identify the suitable hot-melt extrusion processing temperature. The binary drug and polymer (30:70 weight ratio) amorphous solid dispersions were prepared at a processing temperature of 160°C. Differential scanning calorimetry and Fourier transform infrared spectroscopy studies of amorphous solid dispersions revealed the formation of a single-phase amorphous system with intermolecular hydrogen bonding between the drug and polymer. The milled extrudates were compressed into tablets by using extragranular components and evaluated for tabletability. Stability studies of the milled extrudates and tablet formulations were performed to monitor the oxidative degradation impurity (N-oxide). The N-oxide impurity levels in the quetiapine fumarate - Plasdone™ S630 Ultra milled extrudates and tablet formulations were reduced by 2- and 3-folds, respectively, compared to those in quetiapine fumarate - Plasdone™ S630. The reduced oxidative degradation and improved hot-melt extrusion processability of Plasdone™ S630 Ultra make it a better choice for oxidation-labile drugs over Plasdone™ S630 copovidone.

Five-Stage Approach for a Systematic Screening and Development of Etravirine Amorphous Solid Dispersions by Hot-Melt Extrusion.

The aim of this study was to develop a fast, effective, and material sparing screening method to design amorphous solid dispersions (ASDs) of etravirine to drive more effectively the development process, leading to improved bioavailability (BA) and stability. A systematic step-by-step approach was followed by combining theoretical calculations with high-throughput screening (HTS) and software-assisted multivariate statistical analysis. The thermodynamic miscibility and interaction of the drug in several polymers were predicted using Hansen solubility parameters (δ). The selected polymers were evaluated by HTS, using solvent evaporation. Binary compositions were evaluated by their solubilization capacity and physical stability over 2 months. JMP 14.0 was used for multivariate statistical analysis using principal components analysis. Extrusion was performed in Thermo Scientific HAAKE MiniLab II, and extrudates were characterized by assay, related substances, dissolution, and physical state (polarized light microscopy (PLM), Raman spectroscopy, and X-ray powder diffraction (XRPD)). A short stability study was performed where milled extrudates were exposed to 25 °C/60%RH and 40 °C/75%RH for 3 months. Through thermodynamic predictions, five main polymers were selected. The HTS enabled the evaluation of 42 formulations for solubilization capacity and physical stability. The three most promising compositions were selected for hot-melt extrusion (HME) tests. In general, a good correlation was found among the results of theoretical predictions, HTS, and HME. Poly(vinylpyrrolidone) (PVP)-based formulations were shown to be easily extrudable, with low degradation and complete amorphicity, whereas in Soluplus, the drug was not miscible, leading to a high crystalline content. The drug release rate was improved more than two times with PVP, and the manufactured ASD was demonstrated to be stable physically and chemically. A fast and effective screening technique to develop stable ASDs for a poorly soluble drug was successfully developed as applied to etravirine. The given method is easy to use, requires a low amount of drug, and is fairly accurate in predicting the amorphization of the drug when formulated. The success of HME formulation development of etravirine was undoubtedly enhanced with this high-throughput tool, which led to the identification of extrudates with improved biopharmaceutical properties. The structural characterization performed by PLM, XRPD, and Raman spectroscopy demonstrated that the HME prototype was essentially amorphous. The unexpected stability at 40 °C/75%RH was correlated with the presence of molecular interaction characterized by Raman spectroscopy.